This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Don't let a worn, faded bellows detract from your cars exterior. Replace it with this replacement part for original number, 911 799 505 14. This is made by dansk, they offer a complete line of aftermarket replacement bodywork to complement the entire Porsche model range. All dansk aftermarket products are manufactured with quality and cost effectiveness in mind. Sold individually. 1 necessary per car. Passenger's side fitment (lhd).

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Don't let a worn, faded bellows detract from your cars exterior. Replace it with this replacement part for original number, 911 799 505 13. This is made by dansk, they offer a complete line of aftermarket replacement bodywork to complement the entire Porsche model range. All dansk aftermarket products are manufactured with quality and cost effectiveness in mind. Sold individually. 1 necessary per car. Driver's side fitment (lhd).

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Aftermarket complete set of bearings that does not include #8, sourced in Germany. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Quality German aftermarket replacement designed to perform like the original. Sold individually. 6 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Door handles fade over time and the lock mechanisms can fail. If you are restoring or repainting your classic it is a perfect time to replace your door handles. Includes the lock mechanism (without stipulated lock number) and 4 new keys. This is an aftermarket part made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. We recommend replacing the gaskets as well, small door handle gasket, part # 91153163100 and large door handle gasket, part # 9115...(choose a part on the right to read more)

Don't let a worn, faded bellows detract from your cars exterior. Replace it with this replacement part for original number, 911 799 505 16. This is made by dansk, they offer a complete line of aftermarket replacement bodywork to complement the entire Porsche model range. All dansk aftermarket products are manufactured with quality and cost effectiveness in mind. Sold individually. 1 necessary per car. Passenger's side fitment (lhd).

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Made of polyurethane so they will not chip or crack like fiberglass, and are flexible enough to survive small impacts. Simple installation without any modifications to the original bodywork. Sold as a set (left and right). Not for wide body cars (993 turbo or turbo-look). Please note: these are aftermarket products. All aftermarket products need to be prepped, sanded, gaps checked / filled and painted. We only recommend professional installation with a shop that has aftermarket bodywork experience.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This is the sending unit needed to use the vdo 80 psi oil pressure gauge, part number rvdo350040. This unit is appropriate for most four-cylinder engines.

Range: 80 psi / 5 bar
Ohmic range: 10-180
Thread: 1/4-18 npt
# on sender: 30/2

General Fitment

Don't let a worn, faded bellows detract from your cars exterior. Replace it with this replacement part for original number, 911 799 505 15. This is made by dansk, they offer a complete line of aftermarket replacement bodywork to complement the entire Porsche model range. All dansk aftermarket products are manufactured with quality and cost effectiveness in mind. Sold individually. 1 necessary per car. Driver's side fitment (lhd).

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

+ 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - weighs 35.2 lbs (16 kgs) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - includes block off plates & caps to use with either the OEM center muffler or an aftermarket center muffler bypass (with 2 inlets). - replaces the OEM valved side mufflers. Connects to OEM header and catalytic flange and connects to OEM center muffler or bypass. - can be used with bes99107060s1 for an even more aggressive growl. * please note - you will no longer have use of your valves ! Our 991 GT3 side muffler replacements are vastly different than the baffle plated mufflers stu...(choose a part on the right to read more)

Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)

+ 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)

M&m street-sport pdk muffler for 2009- 997.2 / 997.2s

Facts:

- + 18 crank hp & + 15 crank torque
- 2 ½” (63.5 mm) diameter tubing (reduces thermal stress)
- weighs 42 lbs. (19.5 kg)
- replaces OEM primary and secondary mufflers
- reuses OEM headers and 600 cell cats (no cel, retains OEM software)
- t 316 stainless steel for improved durability over t 304
- intoxicating growl at idle, partial throttle and wide open throttle. This system was designed for pdk cars as it has zero drone inside the cabin. It is also perfect for those who are interested in our street sport system but find it a little to loud for their liking.
- no dme programming necessary
-reuses factory tips or any aftermarket tip d...(choose a part on the right to read more)

General Fitment

"brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)

+ 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - net weight is 16.4 kg / 36 lbs. (10 lb savings over stock 3.4 l mufflers) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - 90 db maximum (oem muffler is 75 db for reference). - replaces OEM side mufflers and connects to OEM header and catalytic flange. Please note: this muffler does not include exhaust valves and is meant to replace the OEM system on the base 3.4l 991 (2012+). Power is stated at the crank. This is the very 1st aftermarket muffl...(choose a part on the right to read more)

+ 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)

These are the finest aftermarket visors available for your 914. Made in Germany, they have both the mirror and the map pocket and are made of factory match material

Having to weld up cracks regularly on your current aftermarket racing exhaust? If you are looking for a racing exhaust that can handle abuse at the track, look no further. This exhaust system is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is designed for reliability and performance gains throughout the entire rev range. Not to mention, you directly benefit from everything m&m learns at the track, so their systems designs are never static. Also, each system is tested comprehensively for flow characteristics / rate, thermal stress, cracking, and longevity. Features: + 20 hp & + 19 tq catalytic bypass pipes weighs 55 lbs. (23 kg)...(choose a part on the right to read more)

B&b step headers Porsche 997 Carrera 05+

B&b has just released their high flow headers for the Porsche 997 Carrera or Carrera s. These headers are t304 stainless steel. Designed to improve horsepower and torque, while giving your Porsche 997 a great superior tone. the headers fit with the factory exhaust or with the aftermarket kit.

Headers are sold as a pair and include everything needed for the installation. fits 2005 and up models.

This product is made to order, please allow 7-10 days prior to shipment.


*contact us for special pricing.*

General Fitment

Fabspeed is one of the top fabricators of aftermarket parts. With the introduction of Porsches new production line model of the 997 Carrera it was short after that manufactures such as fabspeed to take this new model into unseen performance. The maxflo supercup exhaust system is completely t304 stainless steel, 14-16 gauge c.n.c. Mandrel bent 2.25" tubing for improved power and sound.


Key features:

Fits all 997 Carrera vehicles 2005-2008
Loud and aggressive supercup style. Recommended for track use only!
System can reuse stock tips or fabspeed's dual-style tips.

General Fitment

Porsche factory uvs sun/heat shields are precisely crafted to fit the windshield of your Porsche, helping to reduce interior temperatures while protecting your leathers and carpets from damaging ultra-violet sun rays. Unlike inferior aftermarket products, this 3-layer shield is light-weight yet rigid, making a better presentation with superior protection year after year. Silver reflective outer surface with gray felt inner finish. Folds accordion style to fit into an included matching storage bag.